Monday, April 28, 2014

Leaking Tap

Leaking tap is a common phenomenon in most households. It is annoying to see that your tap is leaking since it leads to wastage of water and money. But the good thing about it is that you can fix it yourself by just following simple steps.
The most obvious reason why your tap is leaking is that either the washer or the O-ring is worn out and it needs replacement. Sometimes it could be due to the damage on the valve. These problems are encountered if the piping is ageing or the water pressure is above the required magnitude.
The following easy steps can help you in fixing that leaking tap in your homestead.
First you should turn off the water supply to the tap at the main valve. The main valve could be in the street or in the front of your yard. If you reside within a flat the main valve is in most cases located in the bathroom or in the laundry.
Assemble the right tools for the job. They include spanners and any screwdrivers that will suit your tap type. For safety wear gloves while handling those tools and keep them away from children.
Now you get to the actual work. It is advisable that you keep the plug in the basin to avoid disappearance of some of the tap sub-assemblies and to make sure that they don’t get in to the drain which may lead to blockages.
Remove the cover with a flat head screwdriver. This will expose the screws. Undo these screws so that you can remove the handle.
Sometimes the tap may be having metallic covers. You can use you hand or wrench to unscrew. To avoid scratching the chrome, make sure that you place a piece of cloth between the chrome and the wrench.
Remove the tap’s bonnet (headgear) by use of a spanner or a pipe wrench. Avoid using too much force on the nut to prevent fracturing or damaging the pipework. Any damage to the pipe would cause leakages hence you will be forced to seek help from a plumber.
Sometime the nut could be stiff and difficult to turn so you should apply some penetrating oil at the joint. Give it some time to soak usually around ten minutes and try again.
When you completely remove the headgear, you should see body washer, the jumper valve and the 0-ring. The jumper valve will fall by itself.
In some taps the washer has a nut (usually 8mm) holding it. You should remove this nut with a spanner. Apply soaking oil if it is difficult to turn and try again after soaking. If it still difficult to remove, you may be required to replace the washer and the jumper valve as one single unit.
After fitting the damaged/ leaking part, you should apply some grease on the threads before reassembling.
Now you reassemble your tap, close it and open the water at the main valve and check if there are any leakages.
If you have an issue with a blocked drain Perth or hot water system Perth, then you need a 24 hour plumber Perth or an emergency plumber Perth to service you. You might also reach out to a gas plumber Perth to help you. Its important that you have a plumber Perth you can trust. 

Leaking Tap Tricks


Leaking tap is a common phenomenon in most households. It is annoying to see that your tap is leaking since it leads to wastage of water and money. But the good thing about it is that you can fix it yourself by just following simple steps.
The most obvious reason why your tap is leaking is that either the washer or the O-ring is worn out and it needs replacement. Sometimes it could be due to the damage on the valve. These problems are encountered if the piping is ageing or the water pressure is above the required magnitude.
The following easy steps can help you in fixing that leaking tap in your homestead.
First you should turn off the water supply to the tap at the main valve. The main valve could be in the street or in the front of your yard. If you reside within a flat the main valve is in most cases located in the bathroom or in the laundry.
Assemble the right tools for the job. They include spanners and any screwdrivers that will suit your tap type. For safety wear gloves while handling those tools and keep them away from children.
Now you get to the actual work. It is advisable that you keep the plug in the basin to avoid disappearance of some of the tap sub-assemblies and to make sure that they don’t get in to the drain which may lead to blockages.
Remove the cover with a flat head screwdriver. This will expose the screws. Undo these screws so that you can remove the handle.
Sometimes the tap may be having metallic covers. You can use you hand or wrench to unscrew. To avoid scratching the chrome, make sure that you place a piece of cloth between the chrome and the wrench.
Remove the tap’s bonnet (headgear) by use of a spanner or a pipe wrench. Avoid using too much force on the nut to prevent fracturing or damaging the pipework. Any damage to the pipe would cause leakages hence you will be forced to seek help from a plumber.
Sometime the nut could be stiff and difficult to turn so you should apply some penetrating oil at the joint. Give it some time to soak usually around ten minutes and try again.
When you completely remove the headgear, you should see body washer, the jumper valve and the 0-ring. The jumper valve will fall by itself.
In some taps the washer has a nut (usually 8mm) holding it. You should remove this nut with a spanner. Apply soaking oil if it is difficult to turn and try again after soaking. If it still difficult to remove, you may be required to replace the washer and the jumper valve as one single unit.
After fitting the damaged/ leaking part, you should apply some grease on the threads before reassembling.
Now you reassemble your tap, close it and open the water at the main valve and check if there are any leakages.
If you have an issue with a blocked drainGold Coast or hot water systemGold Coast, then you need a 24 hour plumberGold Coast or an emergency plumberGold Coast to service you. You might also reach out to a gas plumberGold Coast to help you. Its important that you have a plumberGold Coast or Gold Coast Plumber you can trust.

Wednesday, April 23, 2014

Lighting A Hot Water System Gold Coast


If you wish to light a hot water system in an easy way then it of the utmost importance to follow the considerations listed in this article:

- Take into account the fact that a malfunctioning pilot light can be a symptom of other problems.
- It is possible that you just need to light the pilot again
- There is a possibility that the solution will cost a certain amount of money in relation to the problem at hand.

After the above is taken into account the following tips and tricks will make your life so much easier. Pay attention and you will be well on your way to bathe with warm water really soon.

Tip # 1 - Make sure your gas supply is on
You wouldn't believe how many headaches could have been avoided if a homeowner would have checked their gas supply before making expensive repairs or embarrassing support calls. This is the first and most important tip, although it's common sense, it's often overlooked.

Tip # 2 - Light your gas hot plate burners 
The orifices in these burners are considerably bigger than that in your gas hot water pilot's burner. For this reason you will markedly speed up the process when you light them all since at this point all the air previously stored in the gas line will have been removed.

Tip # 3 - Make sure the valve responsible for gas isolation or gas stop tap in the hot water system is on
The small isolation valve inside the copper line that provides gas to a hot water system can be located between the ankle height and knee just on the side of most hot water systems. Make sure the tap on top is on. It is important to mention it should be aligned with the copper line, not sitting across it.

Tip # 4 - Remove the hot water system's panelMy advice to do this requires two steps, the first one involves sliding the panels vertically just from the bottom finger hold. The second tip step requires swinging the cover base towards you.

Tip # 5 - Turn the hot water system's pilot button to its flame position
This tip and trick is self explanatory

Tip # 6 - Relight the pilot flame
Push down the flame button while you press the ignition switch from 5 to 10 times. Hold the gas controller pilot for fifteen to twenty seconds and only after that release your pilot flame button

Tip # 7 - Step away when you turn the hot water systemThis tip will assure your own safety and it's important to keep your health intact
If you have an issue with a blocked drain Gold Coast or hot water system Gold Coast, then you need a 24 hour plumber Gold Coast or an emergency plumber Gold Coast to service you. You might also reach out to a gas plumberGold Coast to help you. Its important that you have a plumber Gold Coast or Gold Coast Plumber you can trust.

Hot Water System Options

Hot Water System Options

  • Natural gas – can be used in both storage water heaters and continuous flow heaters.  Natural gas systems are rated according to their energy efficiency and come in both internal and external models.  Gas storage heaters have a smaller capacity than off-peak electric ones as they are able to heat the water up at any time of the day or night as opposed to within a certain time period only. For more information see gas hot water systems.
  • Off peak electricity – has similar running costs to a natural gas system but is only available where the hot water system has a storage capacity 160 liters or more.  The hot water is generally heated overnight for use throughout the day.  It cannot be used by continuous flow systems and is available for both internal and external use.
  • Solar energy – can provide up to eighty percent of your hot water free of charge, making it a very environmentally friendly option.  They are the cheapest systems to operate but do have a high initial purchase price.  All solar hot water systems come with a “booster” source of power (such as gas or electric) to provide hot water during times when there is little sun.  Mains pressure and constant pressure is available. For more information see solar hot water systems.
  • Peak electricity – is used for electric continuous flow units and storage water heaters that are smaller than 160 liters in capacity.  They can be expensive to run but are very popular in areas where space is limited such as in units and apartments. For more information see electric hot water systems.
  • LPG – is used in areas where natural gas is not available.  It is suitable for both continuous flow and storage hot water systems.
  • Solid fuels – this includes wood, coal, briquettes and so forth, so the cost of the fuels can vary widely.  Solid fuels can be used on their own or in conjunction with off peak electricity or solar in constant pressure systems.  They cannot be used with mains pressure systems unless a heat exchanger is used and cannot be used in continuous flow systems.
  • Heat pumps – is high efficiency and uses around seventy percent less electricity than other electric hot water systems.  They work by extracting heat from the atmosphere using a refrigerant gas and a compressor and using that heat to heat water stored in a tank at ground level.

Services/Hiring a Hot Water Systems Specialist

Hot water system suppliers can assist with:
  • Advising on a suitable hot water system
  • Installation (see hot water system installation)
  • Service and repairs (hot water system service and repairs)
  • Supply of the hot water unit
  • Minor plumbing
Ensure that they are able to help you to choose the correct system for the number of people in your household.  They should also allow for possible changes in the use of the hot water system in the future brought about by such things as an expanding family, the introduction of new appliances such as dishwashers and so forth. A reputable plumber can install or replace al types of hot water systems, including electric, gas and solar.
Ensure that the system comes with a warranty, and that the supplier is willing to provide installation in a reasonable time-frame.  It is also useful if your supplier can provide emergency repairs or be able to direct you to someone that does.
The best method to find out about a hot water system is to get in touch with a professional plumbing business such as Melbourne 24 Hour PlumbingMr Plumber Sydney
 If you have an issue with a blocked drain Perth or hot water system Perth, then you need a 24 hour plumber Perth or an emergency plumber Perth to service you. You might also reach out to a gas plumber Perth to help you. Its important that you have a plumber Perth you can trust.